What Is 4M?

November 14, 2026
4 min read

In a nutshell

4M is

the four factors behind any work result: Man, Machine, Material, and Method.

What else?

Learning the four names won’t tell you the cause. But it will tell you where to look.

What Is 4M?

4M is the initials of Man, Machine, Material, and Method.

All four start with M, so it is called 4M.

In quality control, causes that might affect a result are sorted into these four (Satoshi Ebata, “Key Points for Using the Seven QC Tools, Part 5: The Cause-and-Effect Diagram” (JUSE), in Japanese).

What the four cover

  • Man: The people doing the work. Knowledge, experience, familiarity.
  • Machine: Equipment and tools.
  • Material: The raw materials and parts used.
  • Method: Procedures and working conditions.

The terms come from manufacturing, but they also translate to office work.

Machine becomes computers and software, Material becomes the information and data you receive, and Method becomes the workflow.

A translation table and examples of causes are in How to Start Improving Your Work, Part 1 (ma-dailywork, in Japanese).

Sort causes into four

When a problem comes up, ask which of the four it came from.

If you list whatever comes to mind, you lean toward what catches the eye. Set up four drawers first, and you can see which drawer is empty.

The empty spot is where you haven’t suspected yet.

The diagram that uses these four as its big bones and lines up causes along them is the cause-and-effect diagram.

Watch what changes

4M has one more use: watching for what changes.

If you keep doing the same work the same way, the result doesn’t change.

Even so, the people making things take turns, blades wear down, and materials vary slightly in composition.

Quality problems tend to happen at these change points.

So on the factory floor, changes in the 4M are recorded.

If you write down how things were before and after, and what was done, you can trace the cause when a problem appears (“When do quality problems tend to happen, and what should you do to prevent them recurring?” (MONOist, February 8, 2021), in Japanese).

This is called change-point control.

If the result changed, one of the four has changed.

The Man box is not about “whose fault”

What goes in the Man box is not someone’s mistake.

“Only one person knows this well” is not that person’s fault. It is the fault of having no system for sharing knowledge.

Once names start filling the Man box, the discussion turns into a hunt for the culprit.

What you suspect is not the person, but the system that supports the person.

When four aren’t enough

There is also 5M1E, which adds Measurement and Environment to the 4M (Satoshi Ebata, “Key Points for Using the Seven QC Tools, Part 5: The Cause-and-Effect Diagram” (JUSE), in Japanese).

Measurements vary, the room is hot. Use it when many causes don’t fit neatly into any of the four.

Takeaways

Open the four drawers and look for the empty one.

When things go wrong, it’s tempting to keep opening only the Man drawer.

But usually, it’s in a different drawer.

When you’re fuming, toss it into the 4M framework.

Trivia

  • Kaoru Ishikawa: A quality control researcher (1915–1989) and professor at the University of Tokyo. He devised the cause-and-effect diagram and gave birth to QC circles (Kaoru Ishikawa centennial (JUSE), in Japanese).
  • Lot: A batch of products or materials made together under the same conditions.
  • QC circle: A small group of people from the same workplace who get together to improve the quality of their own work.

History

The start

4M has long been the standard set of big bones in the cause-and-effect diagram.

The cause-and-effect diagram was devised by Kaoru Ishikawa, who studied quality control at the University of Tokyo.

It is said to have first been used in 1953 at Kawasaki Steel’s Fukiai Works (Chronology: Professor Ishikawa, who walked alongside Japan’s TQC (JUSE), in Japanese).

However, no source could be found that confirms who first called it “4M,” or when.

Becoming a tool of the workplace

In 1962, QC circles were born: small groups of workplace members who improve quality on their own (JUSE, “QC Circle” magazine, in Japanese).

Splitting causes into four and talking them through came into use in these workplace discussions.

Becoming a tool for watching change

4M came to be used not only when hunting for causes but also when watching for change.

On the factory floor, changes in the 4M are recorded to prevent quality problems and to trace the cause when one happens (MONOist, February 8, 2021, in Japanese).

Today

Quality control courses still teach how to sort causes with 4M or 5M1E (Satoshi Ebata, “Key Points for Using the Seven QC Tools, Part 5: The Cause-and-Effect Diagram” (JUSE), in Japanese).

Timeline

PeriodKey eventsKey people and organizationsCountry or regionNotes
1953Kaoru Ishikawa devises the cause-and-effect diagramKaoru IshikawaJapanUsed at Kawasaki Steel’s Fukiai Works. 4M later became the standard big bones of this diagram. [Chronology: Professor Ishikawa (JUSE), in Japanese](https://www.juse.jp/ishikawa/ningen/Chronology_20150519.pdf)
1962QC circles are bornJUSE (Union of Japanese Scientists and Engineers)JapanSmall groups of workplace members who improve quality on their own. They became the place for splitting causes into four and talking them through. [JUSE, “QC Circle” magazine, in Japanese](https://www.juse.or.jp/qc_circle/about/)
TodayChange-point control, recording changes in the 4M, is practicedManufacturing sitesJapanChanges such as a new operator, a blade replacement, or a different material lot are recorded to prevent quality problems and make causes traceable. [MONOist, February 8, 2021, in Japanese](https://monoist.itmedia.co.jp/mn/spv/2102/08/news010.html)
TodaySorting causes with 4M and 5M1E is taughtJUSEJapan5M1E adds Measurement and Environment to the 4M. [Satoshi Ebata, “Key Points for Using the Seven QC Tools, Part 5,” in Japanese](https://www.juse.or.jp/upload/files/shanai_rensai_Q7_05.pdf)